碳纳米管薄膜的制备及性能研究
边策冯, 钠陈茹* , 郭界, 孟双
大连工业大学纺织与材料工程学院,大连116034
Preparation and property of carbon nanotube film
Bian Ce, Feng Na, Chen Ru, Guo Jie, Meng Shuang
School of Textile and Material Engineering,Dalian Polytechnic University,Dalian 116034
摘要 采用抽滤法制备了一种厚度和纳米孔隙可控的碳纳米管薄膜,探讨优化了碳管种类、溶剂、表面活性剂、超声功率等制备工艺参数,并采用扫描电镜、导电测试仪等技术手段对膜材料的孔径尺寸、形貌特征、力学性能、导电性能等进行了测试表征。结果表明:以TNM3型碳纳米管为原料,以去离子水为溶剂,曲拉通为表面活性剂,在超声功率350W条件下制备的碳纳米管膜综合性能最佳。随着超声功率的增加,碳纳米管薄膜的平均孔径尺寸先递减,后又增大;当碳纳米管含量0.55g/L时,其拉伸强度、模量最高,分别为3.1MPa,0.79MPa;体积电阻率为0.045Ω·cm。
关键词:
碳纳米管
薄膜
导电性
力学性能
Abstract: Carbon nanotube films with the controllable thickness and nano pore were prepared by filtration method.The processing parameters such as the type of carbon nanotube,solvent,surfactant and ultrasonic power were discussed and optimized.The morphology and properties of specimen film including pore size,mechanical properties and electrical conductivity were characterized by SEM,conductive tester and other technologies.The results demonstrated that carbon nanotube film prepared from TNM3,deionized water as solvent,Triton as surfactant and ultrasonic power 350W exhibited the best comprehensive performance.With the increase of ultrasonic power,the average pore size of film decreased,and then increased.Meanwhile,the maximum tensile strength and modulus of film with the content of carbon nanotube 0.55g/L,were 3.1MPa,0.79MPa respectively.The volume resistivity was 0.045Ω·cm.
Key words:
carbon nanotube
film
electrical conductivity
mechanical property
收稿日期: 2017-03-31
发布日期: 2018-09-18
期的出版日期: 2018-08-20
基金资助: 国家质检总局科技计划项目(2014QK109)
通讯作者:
陈茹(1977-),女,讲师,博士。
作者简介: 边策(1993-),男,硕士研究生,主要研究方向为塑料改性与加工。
引用本文:
边策冯, 钠陈茹, 郭界, 孟双. 碳纳米管薄膜的制备及性能研究[J]. 化工新型材料, 2018, 46(8): 75-78.
Bian Ce, Feng Na, Chen Ru, Guo Jie, Meng Shuang. Preparation and property of carbon nanotube film. New Chemical Materials, 2018, 46(8): 75-78.
链接本文:
http://www.hgxx.org/CN/
或
http://www.hgxx.org/CN/Y2018/V46/I8/75
[1] Qu L,Zhao Y,Dai L.Carbon microfibers sheathed with aligned carbon nanotubes:towards multidimensional,multicomponent,and multifunctional nanomaterials[J].Small,2006,2(8-9):1052-1059. [2] Moisala A,Li Q,Kinloch I A,et al.Thermal and electrical conductivity of single- and multi-walled carbon nanotube-epoxy composites[J].Composites Science & Technology,2006,66(10):1285-1288. [3] 张丽丽,丁慧敏,张继堂,等.碳纳米管改性环氧树脂的导热和阻燃性能[J].应用化学,2017,34(1):46-53. [4] 张昊,蔡佩芝,赵东林,等.碳纳米管增强环氧树脂基复合材料的制备及其力学性能[J].北京化工大学学报(自然科学版),2011,38(1):62-67. [5] Thostenson E T,Li W Z,Wang D Z,et al.Carbon nanotube/carbon fiber hybrid multiscale composites[J].Journal of Applied Physics,2002,91(9):6034-6037. [6] Zhang Y,Li Q,Wang W,et al.Efficient and robust reactions for polyethylene covalently grafted carbon nanotubes[J].Macromolecular Chemistry & Physics,2016,218(4):1600449. [7] 张宇轩,李禾,王闯,等.混酸功能化方法对碳纳米管/环氧树脂复合材料电导性能的影响[J].绝缘材料,2017(1):23-27. [8] 贾璐,刘意春,谢明,等.碳纳米管/银氧化锡复合材料的制备及其性能研究[J].现代化工,2017,37(1):104-107. [9] Niyogi S,Hamon M A,Hu H,et al.Chemistry of single-walled carbon nanotubes[J].Accounts of Chemical Research,2014,35(12):1105. [10] Wang Z,Liang Z,Wang B,et al.Processing and property investigation of single-walled carbon nanotube (SWNT) buckypaper/epoxy resin matrix nanocomposites[J].Composites Part A Applied Science & Manufacturing,2004,35(10):1225-1232. [11] Zhang J,Jiang D.Influence of geometries of multi-walled carbon nanotubes on the pore structures of Buckypaper[J].Composites Part A Applied Science & Manufacturing,2012,43(43):469-474. [12] Smajda R,Ákos Kukovecz,Kónya Z,et al.Structure and gas permeability of multi-wall carbon nanotube buckypapers[J].Carbon,2007,45(6):1176-1184. [13] Zhang J,Jiang D,Peng H X.A pressurized filtration technique for fabricating carbon nanotube buckypaper:structure,mechanical and conductive properties[J].Microporous & Mesoporous Materials,2014,184(2):127-133.
[1]
Xiao Yu, Lv Cheng, Zhang Guoyou. Epoxy resin modified by PMMA microsphere wrapped by graphene oxide [J]. New Chemical Materials, 2017, 45(9): 62
-64
.
[2]
Su Wei, Ran Meng, Zhang Ai, Sun Yan. Preparation of sulfur-doped microporous carbon and its adsorption property [J]. New Chemical Materials, 2018, 46(4): 161
-164
.
[3]
Fan Yingge. Study on preparation and optical property of one-dimensional ZnO nanorod by sol-gel dip coating [J]. New Chemical Materials, 2018, 46(4): 189
-192
.
[4]
Zheng Zhen, Ding Chengli, Li Huiping, Fu Jingjing. Synthesis and property of hydrophobic functionalized cotton linter cellulose/SiO2 composite aerogel [J]. New Chemical Materials, 2018, 46(4): 230
-233
.
[5]
Lin Yuan. Research status and application progress of thin film solar cells [J]. New Chemical Materials, 2018, 46(6): 57
-60
.
[6]
Chen Kai, Wang Qiang, Sun Ting, You Min, Xia Zuxi. Research on impact of chemical etching on superhydrophobic surface property [J]. New Chemical Materials, 2018, 46(6): 206
-209
.
[7]
Zheng Dandan, Chang Wei, Xi Qiang, Yu Cuihua. Preparation and photocatalytic activity of Cd1-x Znx S [J]. New Chemical Materials, 2018, 46(5): 181
-183
.
[8]
Han Fei, Zong Yue, Di Song, Wang Shaopo. Adsorption of copper ion in aqueous solution by activated boron nitride [J]. New Chemical Materials, 2018, 46(5): 195
-198
.
[9]
Chang Lin, Zhao Yuntao, Bi Yinping, Ren Yiwei. Preparation and characterization of sodium polystyrene sulfonate grafted polysulfone forward osmosis membrane [J]. New Chemical Materials, 2018, 46(7): 114
-117
.
[10]
Cai Tingting, Liu Rongwei, Wang Yuanyuan, Zhai Yongxing, Duan Ze, Zhang Jian. Preparation and electrochemical performance test of nickel cobalt sulfide/carbon microsphere electrode [J]. New Chemical Materials, 2018, 46(8): 119
-122
.
Viewed
Full text
Abstract
Cited
Shared
Discussed